Hyundai Ioniq: Trip Computer / Tripmeter/Average vehicle speed/ Timer

Tripmeter (1)
- The tripmeter is the total driving distance since the last tripmeter reset.
- To reset the tripmeter, press the OK button on the steering wheel for more
than 1 second when the tripmeter is displayed.
Average Vehicle Speed (2)
- The average vehicle speed is calculated by the total driving distance and
driving time since the last average vehicle speed reset.
- To reset the average vehicle speed, press the OK button on the steering
wheel for more than 1 second when the average vehicle speed is displayed.
Information
- The average vehicle speed is not displayed if the driving distance is
less than 0.19 miles (300 meters) or the driving time is less than 10 seconds,
after resetting the vehicle speed.
- The average vehicle speed will continue to be calculated and will start
to decrease if the vehicle is stopped while the engine is still running (for
example, when the vehicle is in traffic or stopped at a stop light.)
Timer (3)
- The timer is the total driving time since the last timer reset.
- To reset the timer, press the OK button on the steering wheel for more than
1 second when the timer is displayed.
Information
The timer will continue to be counted while the engine is still running (for
example, when the vehicle is in traffic or stopped at a stop light.)
Range (1)
The range is the estimated distance the vehicle can be driven with the remaining
fuel.
If the estimated distance is below 1 mi. (1 km), the trip computer will
display "----" as range...
Digital speedometer
This message shows the speed of the vehicle.
Drive Info display
At the end of each driving cycle, the Driving Info message is displayed...
Other information:
Trouble Symptom ChartsTrouble Symptom 1Trouble Symptom 2
Trouble symptom
Probable cause
Remedy
The set vehicle speed varies greatly upward or downward"Surging" (repeated alternating acceleration and deceleration) occurs after settingMalfunction of the vehicle speed sensor circuitRepair the vehicle speed sensor system, or replace the partMalfunction of ECMCheck input and output signals at ECMTrouble Symptom 3
Trouble symptom
Probable cause
Remedy
The CC system is not canceled when the brake pedal is depressedDamaged or disconnected wiring of the brake pedal switchRepair the harness or replace the brake pedal switchMalfunction of the ECM signalsCheck input and output signals at ECMTrouble Symptom 4
Trouble symptom
Probable cause
Remedy
The CC system is not canceled when the shift lever is moved to the "N" position (It is canceled, however, when the brake pedal is depressed)Damaged or disconnected wiring of inhibitor switch input circuitRepair the harness or repair or replace the inhibitor switchImproper adjustment of inhibitor switchMalfunction of the ECM signalsCheck input and output signals at ECMTrouble Symptom 5
Trouble symptom
Probable cause
Remedy
Cannot decelerate (coast) by using the "SET/–" switchTemporary damaged or disconnected wiring of "SET/–" switch input circuitRepair the harness or replace the "SET/–" switchMalfunction of the ECM signalsCheck input and output signals at ECMTrouble Symptom 6
Trouble symptom
Probable cause
Remedy
Cannot accelerate or resume speed by using the "RES/+" switchDamaged or disconnected wiring, short circuit or "RES/+" switch input circuitRepair the harness or replace the "RES/+" switchMalfunction of the ECM signalsCheck input and output signals at ECMTrouble Symptom 7
Trouble symptom
Probable cause
Remedy
CC system can be set while driving at a vehicle speed of less than 40km/h (25mph), or there is no automatic cancellation at that speedMalfunction of the vehicle-speed sensor circuitRepair the vehicle speed sensor system, or replace the partMalfunction of the ECM signalsCheck input and output signals at ECMTrouble Symptom 8
Trouble symptom
Probable cause
Remedy
The cruise main switch indicator lamp does not illuminate (But CC system is normal)Damaged or disconnected bulb of cruise main switch indicator lampRepair the harness or replace the part...
InspectionCheck if the auto light control operates like a timing chart shown below. Tail lamp output and head lamp (Low) output is controlled based on the auto light sensor's input (illumination intensity) when the Auto Light Switch in Multi-Function Switch is turned ON, and the vehicle is in IGN1 or IGN2 ON Mode...
Categories

Adjusting the side mirrors:
1. Press either the L (driver's side) or R (passenger's side) button (1) to select
the side view mirror you would like to adjust.
read more